Categorization:Harness Component
From the "small space, high speed" requirements of high-end equipment, why ultra-fine coaxial cables are becoming increasingly important.
With the continuous development of laptops, tablets, VR/AR devices, industrial camera equipment, and other high-end electronic products towards thinness, miniaturization, and high performance, the space inside the devices for connecting cables is becoming increasingly limited. However, at the same time, the requirements for the number and transmission performance of signal channels for display, camera, and high-speed data transmission are becoming higher. Under this contradiction of "smaller space, more signals, and higher speed," ultra-thin coaxial cables are gradually becoming an important solution for high-speed signal connections inside high-end electronic devices due to their smaller line diameter, high-density wiring capability, good signal shielding, and high flexibility. I-PEX officially positions the CABLINE®-UA II series, which also emphasizes characteristics such as 0.3mm pitch, small connectors, suitability for narrow spaces, and crossing pivot points; its product series can match AWG 42, 44, 46 Micro-Coaxial Cable, and provide solutions with 26P, 32P, 40P, 50P, and other different pin counts.
Compared with ordinary wires or ribbon cables, the value of extremely thin coaxial cables lies not only in their "thinness" but also in their ability to balance signal transmission, shielding, flexibility, and high-density connections in limited spaces. Especially in areas with narrow spaces, such as notebook screen hinges, camera modules, and high-speed signal connection areas, the cables need to bend, pass through, and be arranged according to the device structure. Traditional thicker wires are often limited by factors such as space occupation, wiring radius, and signal interference. Taking CABLINE-UA II as an example, according to the official data from I-PEX, its connectors use a 0.3mm Contact Pitch, with a height of about 1.27±0.1mm, and a connector depth of about 2.9mm, and are designed for applications crossing hinges; in the official reference examples, a 26-pin cable assembly made of coaxial cables with an outer diameter of about 0.29mm can pass through a hinge or hose with an inner diameter Φ2.65mm.

I-PEX 81467-100B-02-D: engineering parameter analysis of a 40P, 44AWG, 50Ω ultra-thin coaxial cable assembly
Design for engineers, prototyping, and BOM selection for products, as well as for procurement personnel in domestic substitution, supplier development, and cost optimization, our company can provide a compatible alternative ultra-thin coaxial cable solution for the I-PEX 81467-100B-02-D. According to the official I-PEX 81467 engineering drawing, this model belongs to the CABLINE®-UA II 40P HARNESS, with a standard cable length of 200.0±5.0mm, internally using 40 AWG #44, 50Ω, blue Micro-Coaxial Cable, and both ends using CABLINE-UA II series connector structures; the drawing BOM explicitly lists the Housing Ass'y model at the cable end as 20497-040T-30, quantity 2, and配套 with 2679-040-10 Metal Cover, and using UV Glue for Bonding, black Acetate Tape for cable fixation.
From the definition of the Pin, this 40P harness is not simply a direct connection with the same number at both ends, but rather uses a reverse numbering relationship at corresponding positions. The drawings clearly show that Connector 1's 40Pin corresponds to Connector 2's 1Pin, Connector 1's 39Pin corresponds to Connector 2's 2Pin, and so on. Connector 1's 1Pin corresponds to Connector 2's 40Pin. For engineers, this means that when performing compatibility and replacement design, it is not only necessary to confirm surface parameters such as "40Pin" and "200mm", but also to confirm the connector model, Pin Assignment, wire specification, wiring structure, and termination process; for purchasers, it should be avoided to replace based solely on the appearance of the connector or the number of Pins, otherwise, even if the physical assembly can be completed, it does not necessarily mean that it can meet the electrical and structural requirements of the original equipment. The original factory drawings also provide finished product requirements such as AC100V withstand voltage, maximum 2.0mA leakage current, insulation resistance ≥50MΩ under DC100V conditions, and the highest working temperature of the harness being 80℃.
Our company can provide a compatible and alternative cable harness solution for I-PEX 81467-100B-02-D. At the connector end, our company can develop the corresponding cable harness according to the 20497-040T-30 used by this product; the CABLINE-UA II series connectors are compatible with Micro-Coaxial Cable specifications including 42AWG, 44AWG, and 46AWG. Therefore, in actual projects, it is possible to conduct engineering evaluations of different AWG specifications by combining device internal space, signal transmission requirements, mechanical strength, and cable harness structure. It needs to be specially stated that the original drawings for 81467-100B-02-D specify 44AWG, 50Ω wire material; 42AWG and 46AWG belong to the wire material specifications supported by the CABLINE-UA II series at the 20497-040T-30, which does not mean that the original 81467 model can be directly replaced with other AWG without verification.

Section 3: Selection, Compatibility, and Alternative Solutions Reference and Recommendations: How Engineers and Purchasers Can Determine Suitability for Replacement
For customers seeking an alternative product for the I-PEX 81467-100B-02-D connector, it is recommended not to solely focus on whether "the connector can be plugged in," but rather to comprehensively confirm from several dimensions including connector type, pin count, wire material AWG, impedance, length, termination direction, cable molding, and electrical performance. Firstly, if the original design uses the CABLINE-UA II 40P structure, the focus should be on confirming corresponding components such as 20497-040T-30 and checking the accompanying 40Pin structure. Secondly, the wire specification needs to be confirmed according to the original equipment design. The 81467-100B-02-D original drawing uses AWG44, 50Ω Micro-Coaxial Cable, while the CABLINE-UA II series corresponding to 20497-040T-30 can be matched with 42AWG, 44AWG, and 46AWG. Therefore, in new projects or localization designs, selection can be made based on space, flexibility, signal, and reliability requirements.
In terms of length and structure, I-PEX official documents indicate that the CABLINE-UA II standard Harness also offers different Pin counts and length options of 100mm, 200mm, 300mm, etc.; among them, the 40Pin 200mm standard Harness corresponds to the model 81467-100B-02-D. Therefore, for procurement alternatives, it is recommended to establish a complete alternative specification based on the original product's Pin quantity, wire specification, length, connector, and both-end orientation/Pin Assignment rather than simply searching for "similar-looking" products based on the material number. For engineering development, our company can match and develop for ultra-fine coaxial cable, termination structure, and harness size based on the original sample, engineering drawings, BOM, or physical dimensions provided by the customer, and further confirm signal integrity and reliability requirements for specific applications. I-PEX official also clearly states that their standard Harness material number is only valid under the corresponding Harness specification, and if a Harness specification needs to be changed, the Part Number must be updated accordingly. Therefore, actual alternative projects should also be established on the basis of specific specification confirmation and sample verification.
For procurement personnel, the value of adopting compatible alternative solutions is not only reflected in the expansion of supply channels, but more importantly, it can further promote the localization of the supply chain, reduce procurement costs, shorten lead times, and improve supply guarantee capabilities while maintaining the original equipment connection schemes and installation structures. For engineers, a truly valuable alternative solution should be able to "match the size, match the connectors, match the wire parameters, define the Pins correctly, ensure reliable termination, and be verified by actual equipment." Therefore, our company does not simply provide a "thin wire of the same length," but instead focuses on targeted compatible alternative development around ultra-fine coaxial cable assemblies.

Four, ultra-fine coaxial cable束 manufacturing capabilities for high-end electronic equipment and its substitution value
High-end equipment is increasingly adopting extremely fine coaxial cables, not just for the sake of smaller wire diameter, but to simultaneously address multiple engineering issues within limited space, such as high-speed signal transmission, high-density wiring, EMI control, flexible routing, and slim design. According to the official information of the CABLINE-UA II series, its 0.3mm Pitch connectors can provide various signal quantity configurations such as 26P, 32P, 40P, and 50P, and refer to 5Gbps/lane NRZ as the transmission speed; at the same time, its product structure emphasizes suitability for small connector spaces and applications that require passing through pivot axes.
Based on the application requirements of extremely thin coaxial cable bundles in high-end electronic equipment, our company focuses on the production and manufacturing of extremely thin coaxial cable bundles and compatible alternative development. We can carry out product development around the customer's connector model, Pin count, AWG specification, impedance, length, wire exit direction, and actual installation space. For the I-PEX 81467-100B-02-D introduced this time, our company can provide corresponding compatible alternative cable solution, focusing on equipment applications using CABLINE-UA II 40P, 20497-040T-30 connectors, and Micro-Coaxial Cable. We provide selection and sample support for engineers, as well as domestic alternative supply solutions for procurement personnel.

I-PEX 81467-100B-02-D is a typical 40P, 200mm, AWG44, 50Ω ultra-thin coaxial cable assembly, whose core value lies in achieving multi-channel high-speed signal connections within a limited space through the combination of ultra-thin Micro-Coaxial Cable and small high-density connectors. For customers looking for OEM cable replacement, domestic supply, or customized development solutions, it is not only necessary to confirm the product part number but also to perform a systematic match from key parameters such as connectors, AWG, impedance, Pin Assignment, length, and termination structure. Our company can provide I-PEX 81467-100B-02-D compatible alternative cable assembly solutions**, helping customers to achieve more flexible ultra-thin coaxial cable selection and supply in high-end electronic equipment, display modules, camera equipment, and other space-limited high-speed signal applications.
I am【7A Electronic Network】, deeply involved in the production and development of high-speed transmission ultra-fine coaxial cable and precision connectors, can provide stable and reliable alternative solutions, for more details, please contact: Manager Zhang18913228573 (WeChat number).