Categorization:Harness Component
Product Introduction—CABLINE-SS ultra-fine coaxial cable assembly with 40PIN and 0.4mm pitch
In laptops, ultra-thin display devices, precision image modules, and other high-density electronic devices, harnesses not only undertake the signal connection task but also need to consider wiring space, transmission stability, and assembly reliability. In response to these requirements, the I-PEX CABLINE-SS series adopts 0.4mm terminal spacing, low mating height, and a compact connection structure, suitable for high-speed signal connection designs with limited space. The 40PIN standard harness listed in the I-PEX official documentation corresponds to the 82890 series, which has a length of 300mm and a 1-N wire arrangement.
The corresponding ultra-fine coaxial cable assembly model for this product is I-PEX 82890-100B-02-D, and the matching cable end connector model is 20373-R40T-06. The connector is 40PIN with a 0.4mm pitch. According to the I-PEX official model list, this cable assembly uses 40AWG ultra-fine coaxial wire, with a nominal length of 300mm, and the wire position is defined as 1-N. The 20373-R40T-06 is the main model of the 40PIN plug for CABLINE-SS, and the actual cable assembly should also check the corresponding metal shielding shell and complete connector component configuration.
Our company focuses on the production and manufacturing of extremely thin coaxial cables and can develop compatible alternative products according to the corresponding connector, wire material specifications, wire length, and wire sequence requirements. We can provide: I-PEX 82890-100B-02-D compatible alternative cable solution, assist engineers in sample verification, and offer more supply chain options for purchasing personnel.

Two, Selection Knowledge - I-PEX Connector Selection Method for Extremely Thin Coaxial Cable Assemblies
When selecting, engineers should not solely judge the harness compatibility based on connector brand or PIN number, but should comprehensively confirm from aspects such as connector series, contact number, cable specification, wire length, wire position definition, and electrical performance. Taking the 82890-100B-02-D model as an example, the first step should be to confirm that the equipment end uses the CABLINE-SS matching interface and verify the structure and matching requirements of the connector body at the wire end 20373-R40T-06; secondly, confirm that the 40PIN, 0.4mm pitch is consistent with the equipment PCB end interface; finally, check if the 300mm wire length, 1-N wire position definition, and harness routing path meet the overall design requirements. The CABLINE-SS series also has other PIN numbers and different length standard harnesses, but products from the same series do not necessarily mean they can be directly interchangeable without verification.
The wire specification is also an important basis for selection. This standard harness uses AWG 40 ultra-fine coaxial cable. AWG is the American Wire Gauge, and the larger the number, the finer the conductor. When actually replacing it, it is still necessary to check the cable outer diameter, insulation structure, shielding method, and characteristic impedance. The I-PEX official CABLINE-SS documentation has shown the high-speed performance test conditions for 40PIN, AWG 40, 45Ω, and 100mm cables, but this is a specific test configuration and cannot be directly used as a complete performance guarantee for this 300mm harness. The alternative product should be verified by combining the target signal rate and the whole machine line requirements.

Section 3: Selection, Compatibility, and Replacement Solution References and Recommendations
For engineers and purchasers seeking alternative solutions for I-PEX original cable harnesses, it is recommended to prioritize the confirmation of connector mechanical compatibility, followed by verification of electrical performance and cable harness processing quality. For the I-PEX 82890-100B-02-D, the alternative development should be based on the basic conditions of 40PIN, 0.4mm spacing, AWG 40 thin coaxial cable, 300mm nominal length, and 1-N wire position definition, and verify whether the combination of the cable end connector body 20373-R40T-06 and the matching metal shielding shell meets the original design requirements. Pay particular attention to the fact that the 1-N wire sequence cannot be simply understood as a straight-through connection with the same number at both ends. It should be confirmed one by one according to the original drawings of the contact point correspondence, and verified through a continuity test.
During the compatibility assessment process, engineers should focus on the harness dimensions, connector mating status, termination structure, shielding continuity, and signal performance after bending; if the application involves high-speed display or image data transmission, signal integrity indicators such as insertion loss, return loss, and crosstalk should also be evaluated according to system requirements. Purchasing personnel can provide the original material number, drawings, samples, expected purchase quantity, and quality requirements when inquiring to enable suppliers to accurately assess manufacturing conditions, sample cycle, and mass production feasibility. For products of the same series with different lengths or different wire sequences, it is not recommended to replace them directly based on similar models. I-PEX official materials also explicitly remind that when the harness specifications change, the product material number needs to be updated accordingly.

Four, manufacturing and supply advantages — providing support for R&D verification and procurement options
The manufacturing difficulties of extremely thin coaxial cable assemblies are not only due to the thin wire and small connector spacing, but also lie in the need to maintain consistency in processes such as stripping, center conductor termination, shield layer handling, welding alignment, and cable assembly fixation. Our company focuses on the production and manufacturing of extremely thin coaxial cable assemblies and can conduct compatibility and substitution solution evaluations around I-PEX 82890-100B-02-D. We can confirm the specific manufacturing specifications based on the customer-provided drawings, samples, and technical requirements. For the engineering development stage, we can focus on interface matching, wire sequence confirmation, dimensional inspection, and continuity testing; for the procurement and mass production introduction stage, we can further clarify material specifications, inspection standards, batch consistency, and delivery requirements. For projects that require high-speed signal verification, corresponding signal integrity tests should be conducted based on the actual application. Through preliminary specification confirmation and sample verification, we can help customers reduce compatibility risks in the substitution development process and increase the flexibility of supply chain selection.

I-PEX 82890-100B-02-D is a CABLINE-SS 40PIN ultra-thin coaxial cable assembly with standard specifications of 300mm length, AWG 40 wire, 0.4mm connector spacing, and 1-N wire position definition. The mating cable end connector main model is 20373-R40T-06. For enterprises that need to replace original cable assemblies, cost evaluation, or supply chain alternative development, it is recommended to verify the connector structure, wire sequence, cable specification, and high-speed signal performance based on complete drawings and actual samples.
I am【7A Electronic Network】Focusing on the research and development of high-speed ultra-fine coaxial cable assemblies and connectors and alternative solutions. If you have selection or verification needs or product requirements, please contact: Manager Zhang.18913228573 (WeChat same number).